Tuha Oilfield Produced Water Treatment Solution
1. Introduction to oilfield produced water
Produced water is a multiphase system of suspended solids, oil, dissolved gases and dissolved salts that is produced from the reservoir together with crude oil and then subjected to demulsification and separation. Its impurities fall into five categories: suspended solids, colloidal particles, dispersed and floating oil, emulsified oil and dissolved substances.
2. Produced water treatment processes
In China's oilfield oily wastewater treatment there are two main approaches: conventional treatment and advanced treatment. Conventional treatment is the usual choice for high-permeability reservoirs and typically combines sedimentation de-oiling with single- or dual-media filtration.
For low-permeability reservoirs, higher standards are met by following conventional treatment with advanced treatment, which mainly means two- or three-stage filtration.
In produced water treatment, de-oiling is the key step and covers four types: gravity, pressure, flotation and hydrocyclone de-oiling. Filtration is mainly single- or dual-media filtration.
Reinjecting treated produced water that meets the standard matters in several ways: it effectively inhibits clay mineral swelling and greatly reduces potential formation damage; it lowers the risk of environmental pollution; and it saves fresh water, bringing significant economic and environmental benefits.
In short, adopting advanced, efficient produced water treatment technology is an essential and indispensable task for oilfield development and sustainable operation.
3. Characteristics of the Tuha Oilfield
Most developed blocks in the Tuha Oilfield are low-porosity, low-permeability reservoirs with multi-layer, strongly heterogeneous formations and pronounced water sensitivity, salt sensitivity and velocity sensitivity. Given these conditions, Tuha sets strict injection water quality standards: substandard water injected into the formation reduces its intake capacity and affects waterflood performance and normal injection development.
The field's injection capacity cannot meet the balance between injection and production, so formation pressure is maintained at a low level and production capacity cannot be maximised. During treatment and reinjection the water quality gradually deteriorates: suspended solids, corrosion products and bacteria are reinjected with the water, plugging pore throats and reducing the intake of injection wells, some of which fall into under-injection. Once dissolved oxygen, bacteria or carbon dioxide in the injected water exceed the standard, the water becomes more corrosive. Corrosion of water treatment equipment mainly appears as perforation at weld joints.
4. De-oiling technologies for oilfield produced water
Waterflooding plays a vital role in oilfield development: its core purpose is to supplement formation energy and keep reservoir energy in stable balance so that the field can sustain high, stable production. Injecting untreated wastewater, however, damages the reservoir — prolific bacteria, mechanical impurities and iron precipitates plug it, raising injection pressure, lowering injection volume and seriously impairing waterflood displacement efficiency. Cleaning the water before injection is therefore essential.
Because the water comes from the reservoir, the main goals of produced water treatment for reinjection are oil removal and suspended solids removal. The process falls into two stages: de-oiling, which uses the density difference between oil and water together with demulsification and flocculation to separate them; and filtration, which relies on the adsorption and interception of the filter media to hold suspended solids, oil and other impurities on the surface or block them from passing through the bed. The de-oiling stage must be matched to the density and pour point of the crude in the oily water. Technologies used at home and abroad mainly include gravity separator tanks, pressure sedimentation, flotation and hydrocyclone de-oiling.
1. Gravity separator tank: this technology relies on the relative density difference between oil and water. When oily water enters the tank, larger oil droplets rise naturally under buoyancy, while emulsified oil coalesces from small droplets into large ones under the action of a demulsifier (or coagulant). After a certain retention time most of the crude rises to the top of the tank and is removed. The tank is large and the retention time long, so sudden changes in influent flow or quality do not significantly affect effluent quality; however, the footprint is large and the removal of emulsified oil is limited.
2. Pressure sedimentation: the de-oiling equipment is packed with material that promotes droplet coalescence. As oily water passes through the coalescing bed, fine droplets coalesce into larger ones, which speeds up oil rise, shortens retention time and reduces equipment size. The technology combines coalescing inclined plates and markedly improves de-oiling efficiency; however, it adapts less well than a separator tank to changes in influent flow and quality.
3. Flotation de-oiling: large numbers of fine bubbles are generated in the oily water, and suspended oil droplets 0.25–25 μm in size and solid particles attach to the bubbles and rise to the surface, removing oily sludge and suspended solids. Flotation markedly increases the rise velocity of oil droplets and particles and shortens treatment time. It handles large volumes with high efficiency and suits heavy-oil fields and oily water with a high emulsified oil content.
4. Hydrocyclone de-oiling: this technology uses the density difference between oil and water, separating them through unequal centrifugal forces as the liquid spins at high speed. The equipment is compact with high separation efficiency; however, it adapts poorly to oily water whose crude relative density exceeds 0.9.
In recent years, advances in science and technology and the sustained efforts of water treatment specialists have driven continuous innovation in produced water treatment, yielding many new technologies with high efficiency, good quality and high reliability.
5. SINOKLE produced water treatment technology
SINOKLE has combined cyclonic separation with a new generation of micro-bubble generation and dissolved gas flotation technology to develop a first-of-its-kind-in-China new-generation high-efficiency compact enclosed pressurised flotation technology: cyclonic dissolved gas flotation (CDFU: Cyclonic Dissolved Gas Flotation Unit).
In 2018, two CDFU units were used at the Tuha Oilfield to treat produced water. With influent oil ≤1,000 mg/L and suspended solids ≤500 mg/L, the effluent reached oil ≤10 mg/L and suspended solids ≤10 mg/L — an oil removal rate of 99% and a suspended solids removal rate of 98%.

Fig. 1 Equipment on site
Fig. 2 Treatment performance