What Is a Plate Filter Press? Structure, Working Principle and Benefits
What Is a Filter Press?
A filter press is a machine that applies mechanical force on one side of the filter medium to achieve filtration. Plate filter presses are suitable for liquids with viscosity below 50% concentration and relatively low viscosity with low solids content, performing enclosed filtration to meet fine or semi-fine filtration requirements such as purification, sterilization and clarification; with microporous filter membranes selected directly, sterile filtration can be achieved without an additional microporous membrane filter.
Main Components
1. Frame
The frame is the base component of the filter press: a thrust plate and a compression head at the two ends, connected by two beams that support the filter plates, frames and the pressing plate.
Thrust plate: connected to the supports, it anchors one end of the press to the foundation. In a recessed-plate (chamber) press, the center of the thrust plate is the feed port, and there are four ports at the corners: the two upper ports are the inlet for washing liquid or pressing gas, and the two lower ports are outlets (for concealed-flow designs, the filtrate outlet).
Pressing plate: presses the filter plates and frames; rollers on both sides support it so it rolls along the beams.
Beams: load-bearing members. Depending on the environment and anti-corrosion requirements, they can be coated with rigid PVC, polypropylene, stainless-steel cladding or new anti-corrosion coatings.
2. Pressing mechanism
Three types: manual, mechanical and hydraulic.
Manual pressing: a screw-type mechanical jack pushes the pressing plate to clamp the plates.
Mechanical pressing: the mechanism consists of an electric motor (with an advanced overload protector), reducer, gear pair, lead screw and fixed nut. When pressing, the motor turns forward, driving the reducer and gear pair, so the lead screw rotates in the fixed nut and pushes the pressing plate to clamp the plates and frames. As the pressing force grows, the motor load current increases; when it reaches the protector setting, maximum pressing force is attained and the motor is cut off. Because the lead screw and fixed nut have a reliable self-locking thread angle, the pressed state is reliably maintained during operation. On retraction, the motor reverses, and when the block on the pressing plate touches the limit switch, the retraction stops.
Hydraulic pressing: consists of a hydraulic station, oil cylinder, piston, piston rod and the connection between the piston rod and the pressing plate.
Working Principle
The filtration part of a filter press consists of: (1) the thrust plate, (2) the filter plates, (3) the pressing plate, and (4) the filter cloth.
Under external force, the pressing plate clamps all filter plates together, forming chambers between them. The solid-liquid mixture is pumped into the chambers by the feed pump; the liquid passes through the filter cloth and leaves through the concealed ports of the plates, while the solids are retained by the cloth and gradually accumulate in the plate chambers, forming the filter cake. For easy handling and transport of the cake, and to avoid secondary pollution of the environment, the moisture content of the cake when it leaves the plates is generally 75%.
It follows that the chamber volume between the filter plates cannot be changed. Under the same operating conditions (e.g., feed pump power and operating time), a membrane-type plate press can apply mechanical force to reduce the chamber volume and squeeze water out of the cake, further lowering its moisture content.
Operation and Equipment Configuration
Reasonable matching between the feed pump and the filter press;
A filter press can work continuously 24 hours a day, changing the operation from two shifts to four shifts per day;
Typical auxiliary equipment: sewage lifting pumps, dosing pumps, agitators, air compressors, feed pumps and the filter press;
The service life of a filter press is 7-10 years.
Benefits of the Automated Filter-Press Scheme
For a project with a total investment of 6 million CNY, of which 4 million is equipment investment, a main-equipment life of 15 years and an operating cost of 1.36 million CNY per year, the automated scheme delivers:
The entire filter-press cycle is shortened, raising work efficiency by about 60%;
Energy savings of about 37.5%, with simple operation and easy maintenance and repair;
Annual investment-cost savings of about 43%, with the investment recovered in roughly two years;
Low cake moisture, easy handling and transport, and no secondary environmental pollution.