Vacuum Tower Overhead Condensate: Why It Emulsifies and How to Remove the Oil
Where the Oil Comes From
Crude oil processing first splits the crude into different straight-run fractions by boiling point, then removes the non-ideal components from these fractions according to product quality standards, or converts them by chemical reaction into the required components, thereby producing a series of qualified petroleum products. Distillation is the most common and economical separation method and is the first processing step of crude oil in a refinery.

Through atmospheric and vacuum distillation the crude oil is separated into different fractions. Generally, the overhead oil vapor is condensed, and oil, water and gas are separated in the oil-water separator. Because the condensed wastewater usually contains high concentrations of sulfides, it is known as sulfurous (sour) wastewater and, after steam stripping, is normally sent to downstream units as purified water for reuse.
In recent years, however, with crude oils becoming poorer in quality and more diverse, the atmospheric/vacuum overhead condensate easily emulsifies and carries oil. This not only causes losses of light oil products but also severely impacts downstream units in the following ways:
Destroyed gas-liquid equilibrium: oil acts as a surfactant; under the intense gas-water contact in the stripping column it foams readily. Large amounts of foam prevent effective mass transfer between the gas and liquid phases, increase steam consumption, cause operating fluctuations and reduce the column capacity.
Tray and reboiler fouling: emulsified oil is complex in composition. When the oil content is high, oil accumulates and plugs key locations such as trays and reboilers, which reduces mass-transfer efficiency and may cause local overheating, lowering overall equipment performance and service life.
By-product contamination: during stripping, hydrocarbons in the sour water produce black sulfur, and oil carried in liquid ammonia affects product quality.
Why the Emulsion Is So Stable
As crude quality deteriorates, inferior heavy oils contain natural surfactants (asphaltenes, resins, petroleum acids); production chemicals added during extraction (alkylbenzene sulfonates, fatty-alcohol polyoxyethylene ethers, etc.) and corrosion inhibitors added during distillation (caustic solutions) form anionic surfactants. These are weakly hydrated and enter directly into the inner Helmholtz plane, replacing the water-dipole layer and adsorbing specifically on oil-droplet surfaces, lowering the oil-water interfacial tension. Meanwhile the negative charges on the droplet surface and the anionic surfactants form a Stern electric double layer, producing a zeta (ζ) potential. Because the liquid temperature is high, diffusion is more pronounced: the thicker the Stern double layer, the higher the ζ potential and the greater the repulsive force between droplets. Oriented adsorption at the oil-water interface forms a stable, robust interfacial film that prevents coalescence when droplets collide - this is why oil-in-water emulsions in atmospheric/vacuum overhead water remain stable, do not separate even after long settling, and carry a high oil load.
Deoiling Before Stripping
To guarantee the efficiency and stability of the stripping process, the oil must be removed before the sour water enters the stripping column, generally to below 50 mg/L. The deoiling technologies currently used in various plants are summarized in the figure below.

Among them, coalescence (coarse-graining) technology attracts particular attention thanks to the following advantages:
Small footprint;
Low equipment cost;
No chemical dosing, so no secondary pollution;
Low energy consumption and large treatment capacity.
Coalescence deoiling, also called the coalescence method, packs coalescing material into a coalescing device through which the oily wastewater flows and the oil coalesces and separates. The principle is based on the different affinities of the oil and water phases for the coalescing material: the immiscible dispersed oil droplets and water particles in the wastewater are coalesced separately, enlarging the particle size. Small oil droplets are intercepted by the coalescing material, stay on its surface and in its pores, and form larger oil films or droplets; under buoyancy and hydraulic forces they detach from the coalescing surface and pores, overcome the flow resistance, and rise faster, thereby achieving oil-water separation.
Industrial Experience
SINOKLE has accumulated extensive experimental exploration and industrial application experience in deoiling. In 2021, at a PetroChina refinery in Chad, a combined "filtration + coalescing deoiling" process was adopted for sulfurous wastewater pretreatment at 20 m³/h: with an influent oil concentration of 500 mg/L, the effluent oil concentration was below 15 mg/L, an oil-removal efficiency greater than 97%.