What Is Oily Sludge? Sources, Composition, Hazards and Treatment Methods

2026-11-20 13:07:36
立即下载

Where Oily Sludge Comes From

Oily sludge arises through several main routes, each with its own characteristics.

1. Land contaminated by crude oil. Large areas can be covered by oily sludge spread over the ground surface.

2. Oily sludge generated during oilfield gathering and transfer. The oily sludge from crude-oil production mainly originates in the surface treatment system. Sludge generated during produced-water treatment - together with the flocs formed by the clarifier chemicals dosed in water purification, equipment and pipeline corrosion products, scale and bacterial residues - makes up this oily sludge. It is typically high in oil content, viscous, fine-grained and difficult to dewater; it not only degrades the quality of transported crude but also makes injection water quality and discharged wastewater hard to bring up to standard.

The oily sludge generated during oilfield gathering and transfer mainly comes from tank bottoms, settling tanks, wastewater tanks and API separator bottoms at transfer and combined stations, oily-water treatment facilities at refineries, light-hydrocarbon processing plants and natural gas purification units, plus crude spilled on the ground from drilling, oilfield operations and pipeline perforation. When product tanks store oil, small amounts of mechanical impurities, sand, soil, heavy-metal salts and heavy oily components such as paraffin and asphaltene settle to the tank bottom and form tank-bottom sludge. This sludge is complex in composition, containing large amounts of aged crude, wax, asphaltene, colloids and suspended solids, bacteria, salts, acid gases and corrosion products; the coagulants, corrosion inhibitors, scale inhibitors and biocides dosed during wastewater treatment also end up mixed into it. During the periodic tank cleaning every 3-6 years, tank-bottom sludge accounts for roughly 1% of tank volume. Tank-bottom sludge is characterized by an extremely high hydrocarbon (oil) content: a typical analysis shows about 25% water, 5% inorganic sediment such as sand, and about 70% hydrocarbons, of which asphaltene is 7.8%, paraffin 6%, and sludge ash 4.8%.

3. Oily sludge from refinery wastewater treatment yards. At refinery wastewater treatment yards, oily sludge comes mainly from API separator bottoms, flotation scum and crude tank bottoms - known as the "three sludges". These sludges differ in composition, usually containing 10%-50% oil and 40%-90% water, along with a certain amount of solids.

4. Contaminated soil from oil use in steel smelting and similar industries.

5. Offshore oil production and shipping. Coastlines and river banks polluted by heavy oil hydrocarbons from offshore production and shipbuilding/repair, seabed oily sludge, and water and land contamination caused by oil spills from tanker and tank-truck accidents.

Composition and Properties

Oily sludge is generally a stable suspension-emulsion system composed of oil-in-water (O/W) and water-in-oil (W/O) emulsions plus suspended solids. It dewaters poorly; its composition and physical properties vary greatly with wastewater quality, treatment process and dosed chemicals; its oil content differs widely, and part of it has recycling value. Oily sludge also contains heavy metals and other harmful substances, and can even carry radioactive contamination.

Environmental Hazards

Oily sludge is bulky. If discharged untreated, it not only occupies large areas of farmland but also pollutes the surrounding soil, water and air and produces foul-smelling gases. The sludge carries large amounts of pathogenic bacteria and parasite eggs; heavy metals such as copper, zinc, chromium and mercury; salts; and large quantities of odorous toxic substances such as benzene series compounds, phenols, polychlorinated biphenyls, dioxins, anthracene and pyrene, as well as radionuclides and other refractory toxic and harmful substances. Random landfilling causes severe groundwater pollution and destroys crops, trees and natural vegetation.

The composition of oily sludge varies with the cause of contamination. Oily sludge from oilfields and storage tanks generally contains 10%-50% oil and 40%-90% water, and its generation, quantity and composition are fairly stable. The treatment methods below apply to it; harmless treatment of oily sludge from other sources can follow the same reference.

Treatment Principles and Methods

The ultimate goal of oily sludge treatment is reduction, resource recovery and harmless disposal guided by the principles of volume reduction, resource utilization and harmlessness. Commonly used methods include solvent extraction, incineration, biological treatment, coking, sludge profile control and comprehensive utilization. The first steps are always dewatering and conditioning:

(1) Dewatering of oily sludge. Treatment begins with dewatering. Water in oily sludge exists in four forms: free water, interstitial water, vicinal (surface) water and chemically bound water. Common dewatering methods and their effects are compared below:

Dewatering methodEquipmentMoisture after dewatering (%)Product state
ThickeningGravity, flotation or centrifugal thickening95-97Paste-like
Natural dryingNatural drying beds, sand drying beds70-80Cake
Vacuum filtrationVacuum drum, vacuum disc filters60-80Cake
Pressure filtrationPlate-and-frame filter press45-80Cake
Roller pressingBelt filter press78-86Cake
CentrifugationDecanter centrifuge80-85Cake
DryingThermal dryer10-40Powder / granules
IncinerationIncinerator0-10Ash

The black, viscous oily sludge concentrate after gravity-settling dewatering is a multiphase colloidal system composed of O/W and W/O emulsions plus suspended solids, with fairly complex composition. Because sludge particles adsorb like charges and repel each other, and because the mixture is fully emulsified, separating oil, water and sludge solids is difficult. Conditioning agents must be added to separate the crude from solid particles, coalesce oil droplets and sink the previously dosed chemicals with the solid impurities, achieving complete three-phase separation of oil, water and solids. That is, different flocculants, demulsifiers and pH adjusters are added; an appropriate dewatering method is selected; and measures such as heating to reduce viscosity (best above 50 °C) complete oil-water-solids separation.

(2) Solvent extraction. Extraction uses the "like dissolves like" principle: a suitable organic solvent is selected as extractant to recover the crude oil in the sludge. Supercritical fluid extraction is an emerging oily-sludge extraction technology still under development. A substance that is gaseous at ambient temperature and pressure is compressed to a liquid state under high pressure and used as extractant; thanks to its enormous dissolving capacity, the extractant is easy to recover and recycle. Common supercritical extractants include methane, ethylene, ethane, propane and carbon dioxide - substances with high critical temperatures and low critical pressures that are cheap, easy to obtain, low in density and easy to separate. Extraction of oily sludge is still at the experimental development stage. Its advantage is thorough treatment: most petroleum substances can be extracted and recovered. Because the extractant is expensive and suffers losses in the process, however, extraction is costly and has not yet been applied to refinery oily sludge. The key to developing this technology is a high cost-performance extractant.

(3) Incineration. Oily sludge that has been pre-dewatered and thickened is sent to an incinerator and burned at 800-850 °C for about 30 minutes; the ash residue then needs further treatment. Domestic incinerator types mainly include box-type, fixed-bed, fluidized-bed, rake furnace and rotary kiln. Incineration's advantage is that almost all harmful substances are destroyed, reducing environmental hazard and achieving good volume reduction with safe handling; its disadvantages are secondary pollution generated during burning and the waste of valuable resources.

(4) Biological treatment. Biological technologies for wet sludge mainly include landfarming, composting and sludge bioreactors, using microorganisms to degrade the petroleum hydrocarbons in oily sludge into harmless soil constituents. Landfarming can pollute land and groundwater, so it has been discontinued in some developed countries. Composting mixes the oily waste with suitable bulking material and piles it so natural microorganisms degrade the hydrocarbons - an effective biological method in which the hydrocarbon half-life is about 2 weeks; treated waste can be landfilled or applied to farmland. A bioreactor is a vessel in which oily sludge is diluted into a slurry in a nutrient medium. Because oxygenation, temperature and nutrients can be controlled artificially, hydrocarbon biodegradation is faster than in other biological processes; adding acclimated high-efficiency hydrocarbon-oxidizing bacteria accelerates degradation further, with a biodegradation half-life of 5 days at 5% solids loading. The bioreactor method suits oily sludge as well as oil-contaminated soil and oily drill cuttings: after treatment the liquid portion can be discharged to a disposal well (pit, pond) or reused, and the solid portion applied to farmland. The bioreactor method can also serve as pretreatment of petroleum-industry waste to reduce hydrocarbon content before other treatment.

(5) Coking. Oily sludge contains a certain amount of mineral oil, mainly alkanes, cycloalkanes, aromatics, olefins, resins and asphaltenes. Coking treats oily sludge by using thermal cracking and thermal condensation of hydrocarbons at high temperature to produce liquid oil products, non-condensable gas and coke. The reaction temperature is 490 °C at atmospheric pressure, and the liquid products are mainly gasoline, diesel and wax oil.

(6) Profile control. Oily sludge from produced water is well compatible with the reservoir. Using the sludge as a base material, chemical treatment with suitable additives suspends its solid particles, extends suspension time and increases injection depth, effectively raising plugging strength while dispersing the oil fraction into a uniform, stable emulsion. The emulsified suspension prepared from oily sludge serves as a profile-control agent for water injection wells: after it reaches a certain depth in the formation, formation water dilution and rock adsorption break the emulsified suspension; the clay adsorbs resins and waxes and, through them, agglomerates into larger "aggregate structures" that settle in the large pores, narrowing their diameter and plugging high-permeability zones. This increases the flow resistance of injected water, forces it to change direction, and improves sweep volume. With optimized execution, the sludge plugs only high-permeability zones without damaging medium- and low-permeability layers. The treated sludge must meet these technical indices as a profile-control agent: low viscosity (≤ 0.3 Pa·s) with good pumpability; good suspension after the suspending agent is added, with a settling time greater than 3 h.

(7) Other methods. Besides the above, there are landfarming, sludge solidification, chemical demulsification, solid-liquid separation and landfill technologies; comprehensive utilization generally uses oily sludge for road paving, brick making and briquette production. Abroad there are also low-temperature pyrolysis technologies and methods that separate oil from sludge using solvents combined with low-frequency acoustic waves.

Advanced pyrolysis technology in oily sludge treatment is increasingly applied as well, recovering oil while achieving volume reduction and harmless disposal.

Mobile phone/Whatsapp

+86 18926412206

Email

marketing@sinokle.com

Address

Room 2301, Building 1B, Smart Home, Baolong Street, Longgang District, Shenzhen, China

Phone
E-mail
Map
QQ Service