Why Reinjection Water in Polymer-Flooded Blocks Is So Hard to Treat: A Complete Breakdown from Polymer Viscosity Reduction to Demulsification and Oil Removal

2026-11-18 10:49:47
立即下载

Reinjection water treatment in polymer-flooded blocks has become one of the most representative challenges in oilfield water management in recent years. Unlike conventional produced water, it cannot be handled simply by settling plus filtration: at many sites the traditional train begins to slip once polymer injection starts, showing falling water quality, caked filter media and rising sludge volumes. This article takes the problem apart, from root cause through to process design.

I. What Exactly Makes Polymer-Laden Water So Difficult

Reinjection water from polymer-flooded blocks carries a high concentration of polymer, and its typical signature is high polymer content, high viscosity, high oil content and strong emulsion stability. The polymer raises the viscosity of the aqueous phase and at the same time adsorbs onto the oil-water interface, strengthening the interfacial film; once the oil droplets are broken up they neither rise easily nor coalesce, forming a stable emulsion system.

These four characteristics are interlinked. High viscosity weakens the separation efficiency of gravity settling and flotation; strong emulsion stability means residence time alone cannot separate the phases at all; and high oil content pushes the downstream filtration unit to its load limit. The difficulty does not increase linearly, it compounds.

II. Why the Traditional Three-Stage Train with Flotation Fails

The conventional three-stage-plus-flotation flow was designed, in essence, around the properties of ordinary produced water. The properties of polymer-laden water have changed, yet the flow offers no corresponding means of demulsification or viscosity reduction, so oil removal efficiency falls short, the effluent cannot meet reinjection water quality requirements, and a large volume of oily sludge is generated along the way.

The rise in sludge volume is often underestimated. Oily sludge is a material that requires dedicated disposal, and the larger the volume, the higher the cost of transport, disposal and management. When the traditional flow loses efficiency under polymer-laden conditions it usually also needs higher chemical dosing, which inflates the sludge volume further and creates a vicious circle.

III. The Overlooked Problem of Caked Filter Media

The effect of high-molecular-weight polymer on the filtration unit is subtle but persistent. After entering the filter bed the polymer binds the originally loose media together into a caked layer; filtration resistance and differential pressure rise, backwashing can no longer restore the bed, and media life is shortened. Operators usually see only frequent backwashing and deteriorating effluent, and do not necessarily realise that the root cause lies in the polymer upstream.

This also explains why strengthening filtration alone cannot solve the problem. As long as the polymer remains, even the best filter media only buys a slightly longer cycle. To truly clear this hurdle, the polymer has to be dealt with before filtration.

IV. CDOF Catalytic Oxidation Viscosity Reduction Approach

The SINOKLE solution is built around CDOF catalytic oxidation viscosity reduction. CDOF is an integrated ozone advanced catalytic oxidation and flotation unit that combines multiple ozone catalytic oxidation technologies, hydrodynamic cavitation and cyclonic flotation, and comprises an oxygen generation system, an ozone generation system, a high-efficiency ozone dosing system, a multiple catalytic reaction system and a cyclonic dissolved-gas flotation system.

sinokle

Its technical strength lies in the synergy of several mechanisms: homogeneous and heterogeneous catalysis act together, hydrodynamic cavitation creates locally extreme conditions, supercritical catalytic oxidation accelerates the reaction rate, and cyclonic dissolved-gas flotation completes the separation, all under closed and pressurised conditions. This combination achieves good removal of petroleum hydrocarbons, suspended solids, colloids, COD, bacteria and other pollutants.

sinokle

Applied to polymer-laden water, CDOF takes on the task of chain scission and viscosity reduction. Through its patented oxidation technology the unit rapidly breaks down and degrades the large polymer molecules in the water, the viscosity drops sharply and the stability of the emulsion is weakened; at the same time the chronic caking of downstream filter media is resolved. This is the starting point of the whole process and the most fundamental difference from a conventional train.

V. CDFU and the Finishing Touch of Fine Filtration

Only once the viscosity has come down can the oil removal step be efficient. CDFU uses microbubbles together with cyclonic flotation to break the emulsion precisely and rapidly remove free oil, emulsified oil and suspended solids. The microbubbles give fine oil droplets an attachment surface, the cyclone field amplifies the density difference and speeds up separation, and demulsification targets the residual interfacial film; working together, these mechanisms take out in a single step the oil released by the upstream viscosity reduction.

sinokle

The produced water then passes through a fine filter for deep polishing and flows directly into the reinjection buffer tank for on-spec reinjection. Because the polymer has already been broken down by chain scission in the CDOF stage, the risk of media caking is greatly reduced and the filtration unit can run steadily, easing the pressure of backwashing and media replacement.

VI. Closing the Loop: Centralised Crude Recovery

One more detail of this process deserves attention: CDOF and CDFU collect the recovered crude oil, which goes to the crude tank for reuse. Oil removal is not about turning oil into waste; it is about sending it back where it belongs. For a polymer-flooded block this oil has recovery value; for the water treatment system it means less oily sludge is generated.

sinokle

The complete process route is as follows: the polymer-laden water passes a coarse filter that traps debris, then enters CDOF for catalytic oxidation viscosity reduction, and then CDFU cyclonic dissolved-gas flotation completes demulsification and oil removal; the produced water is polished in a fine filter, flows into the reinjection buffer tank and is finally reinjected into the reservoir. The unit runs fully enclosed and pressurised, so neither ozone nor oil vapour escapes, and the skid-mounted design makes on-site layout and retrofit tie-in straightforward.

VII. Summary

The key to reinjection water treatment in polymer-flooded blocks is to remove the polymer, the root variable, first, rather than patching things up repeatedly at the tail end. SINOKLE takes CDOF catalytic oxidation viscosity reduction as the core and pairs it with CDFU cyclonic dissolved-gas flotation and fine filtration, tackling viscosity, emulsification and media caking as one connected problem and offering a complete process route for bringing polymer-laden water to reinjection quality.


Mobile phone/Whatsapp

+86 18926412206

Email

marketing@sinokle.com

Address

Room 2301, Building 1B, Smart Home, Baolong Street, Longgang District, Shenzhen, China

Phone
E-mail
Map
QQ Service