What Is an EDI System?
Therefore, the EDI system here is a pure water production system.
The historical evolution of ultrapure water production with EDI ultrapure water equipment: Stage 1: pretreatment filter → cation bed → anion bed → mixed bed; Stage 2: pretreatment filter → reverse osmosis → mixed bed; current stage: pretreatment filter → reverse osmosis → EDI (no acid or alkali needed). For decades, mixed-bed ion exchange technology (D) has been the standard process for ultrapure water production. Because it requires periodic regeneration that consumes large amounts of chemicals (acids and alkalis) and industrial pure water and causes certain environmental problems, acid- and alkali-free ultrapure water systems needed to be developed. Precisely because conventional ion exchange has become increasingly unable to meet the demands of modern industry and environmental protection, EDI technology—which combines membranes, resin and electrochemical principles—has become a revolution in water treatment. Its ion exchange resin is regenerated with electric energy rather than acid and alkali, so it better meets the environmental requirements of today's world.
Since EDI membrane stack technology was industrialized in 1986, thousands of EDI systems have been installed worldwide, developing vigorously especially in the pharmaceutical, semiconductor, power and surface-cleaning industries, and also being widely used in wastewater treatment, beverages, microbiology and other fields.
EDI equipment is applied after the reverse osmosis system, replacing conventional mixed-bed ion exchange technology (MB-DI) to produce stable ultrapure water. Compared with mixed-bed ion exchange technology, EDI offers the following advantages:
EDI units generally use two-stage reverse osmosis (RO) permeate as feed. At 25°C the conductivity of two-stage RO permeate is typically 0.5–5 µS/cm (it varies with the conductivity of the first-stage RO water, but normal two-stage RO water should not exceed this range). After EDI treatment at 25°C, the resistivity of the product water can reach 18.25 MΩ·cm or higher (the theoretical resistivity of absolutely pure water at pH 7 is about 18.29 MΩ·cm, and that of ultrapure water is about 18.248 MΩ·cm — in other words, properly operated EDI product water fully meets the ultrapure water standard in resistivity). Depending on process water uses and actual system configuration, EDI systems are widely used to produce pure water with resistivity requirements of 10–18 MΩ·cm (25°C).
(1) Effect of feed conductivity. At the same operating current, as the conductivity of the raw water increases, the removal rate of weak electrolytes by the EDI decreases and the conductivity of the product water rises. If the raw water conductivity is low, the ion content is also low; the low ion concentration produces a larger electromotive force gradient on the surfaces of the resin and membranes in the dilute chamber, which enhances water dissociation, increases the limiting current and generates more H+ and OH−, giving good regeneration of the anion and cation exchange resins filled in the dilute chamber.
(2) Effect of operating voltage-current. As the operating current increases, product water quality keeps improving. But if the current is raised beyond the peak point, the H+ and OH− ions produced by water dissociation become excessive — apart from those used for resin regeneration, large numbers of surplus ions act as current-carrying ions; accumulation and clogging occur during their migration, and even back-diffusion takes place, so product water quality deteriorates.
(3) Effect of turbidity and silt density index (SDI). The product water channels of EDI modules are filled with ion exchange resin; excessively high turbidity or SDI clogs the channels, raising the system pressure drop and reducing water output.
(4) Effect of hardness. If the residual hardness of the EDI feed is too high, scaling occurs on the membrane surfaces of the concentrate channel, concentrate flow decreases and product resistivity falls, degrading water quality; in severe cases the concentrate and electrode water channels of the module become blocked, and the module is destroyed by internal heating.
(5) Effect of TOC (total organic carbon). If the organic content of the feed is too high, it causes organic fouling of the resin and the permselective membranes, raising operating voltage and degrading product water quality; organic colloids also tend to form in the concentrate channel and clog it.
(6) Effect of CO2 in the feed. HCO3− formed from CO2 in the feed is a weak electrolyte that easily penetrates the ion exchange resin bed and degrades product water quality.
(7) Effect of total exchangeable anions (TEA). High TEA lowers EDI product resistivity or requires a higher EDI operating current, and excessively high operating current increases the system current and the residual chlorine concentration in the electrode water, which is bad for electrode membrane life.
In addition, feed temperature, pH, SiO2 and oxidants also affect EDI system operation.
(4) Feed hardness control. Combined with CO2 removal, soften the RO feed or dose alkali; when the feed salinity is high, add another RO stage or nanofiltration in combination with desalting.
(2) Operating voltage-current control. An appropriate operating voltage-current point should be selected when the system runs. Meanwhile, there is a limiting voltage-current point on the voltage-current curve of the EDI unit, related to feed water quality, membrane and resin performance, membrane pair structure and other factors. So that a given amount of water is dissociated to generate sufficient H+ and OH− to regenerate a given amount of ion exchange resin, the selected operating point of the EDI unit must be above the limiting voltage-current point.
(3) Feed CO2 control. Dose alkali before the RO to adjust pH and remove CO2 as much as possible, or use a degassing tower or degassing membrane to remove CO2.
(1) Feed conductivity control. Strictly control the conductivity in pretreatment so that the EDI feed conductivity is below 40 µS/cm, which ensures qualified product conductivity and removal of weak electrolytes.
(5) TOC control. Add another RO stage to meet the TOC requirement together with other specifications.
(6) Turbidity and SDI control. Turbidity and SDI are among the main feed control indicators for the RO system; qualified RO product water can generally satisfy the EDI feed requirements.
(7) Fe control. Keep the Fe content of the EDI feed below 0.01 during operation.
(8) EDI feed water quality requirements
Based on the above analysis, meeting the feed water quality requirements listed in the table ensures that the EDI product water meets the high-purity water requirements of semiconductor manufacturing in the electronics industry.
EDI technology is widely accepted by the pharmaceutical, microelectronics and power generation industries and by laboratories. Its applications in surface cleaning, surface coating, electrolysis and the chemical industry are also expanding.
1. Semiconductor and electronics industry: ultrapure water
2. Biopharmaceutical industry: purified water