Cultivating Activated Sludge Seed: Preparation, Natural Growth and Seeding Methods
Activated sludge can be cultivated in more than one way, but each method demands a different amount of time, labour and material. The method has to be chosen to suit the wastewater quality, the climate and the conditions the plant can realistically provide.
Preparation Before Cultivation Starts
1. Every structure is complete, the basins have been cleaned of construction debris, a hydrostatic test has shown no leakage, no settlement and no displacement, and the works have been accepted to the relevant specification.
2. All electrical, mechanical and piping work is finished, individual equipment runs and linked no-load trials are satisfactory, and acceptance to the relevant specification and manuals is complete.
3. Where resources allow, the plant sets up the basic routine laboratory tests — pH, water temperature, COD, dissolved oxygen and microscopic examination of the biomass — to guide both the cultivation itself and day-to-day operation.
4. Survey the baseline data: the diurnal variation in flow; water quality (pH, temperature, COD, BOD5/CODCr, nitrogen, phosphorus, toxic substances) and how it varies; and the technical parameters of every structure and item of equipment. Where possible, record the background quality of the receiving water — the river that takes the discharge, for example — so that its condition can be compared years later.
5. Stock the nutrients the wastewater will need — carbon, nitrogen and phosphorus sources — so that any shortfall can be made up. If the seeding method is to be used, also arrange a supply of dried or thickened sludge from a plant treating similar wastewater, to serve as the seed culture.
6. Operators should know the piping layout and the utilities, and understand the basic course of sludge cultivation and the control requirements.
7. Staff must be in place. Once cultivation and acclimation begin, the plant normally runs continuously and cannot be left unattended.
8. Prepare the laboratory and operating log sheets and put the first management rules in place, so that start-up and the operation that follows proceed in an orderly way.
Natural Cultivation (Direct Cultivation)
Natural cultivation, also called direct cultivation, takes the small population of micro-organisms already present in the wastewater and multiplies it step by step. Municipal sewage and industrial wastewater that is nutritionally fairly complete and low in toxicity — food processing and meat processing effluent, for instance — can be cultivated this way, but it takes longer. Natural cultivation divides into batch and continuous variants.
1. Batch cultivation. Fill the aeration tank with wastewater and aerate without feeding (aeration only, no inflow). After a few days stop the air, let the tank settle for one hour, draw off roughly one fifth of the upper layer and refill with the same volume of fresh wastewater. Repeat the cycle of unaerated-feed aeration, settling and refilling, increasing the volume each time and shortening the aeration period each time. In spring and autumn a sludge begins to appear in about two to three weeks. When the mixed liquor suspended solids in the aeration tank reach about 1 g/L, continuous feed and aeration can start. Because the sludge concentration is low at first, little sludge accumulates in the clarifier and the return rate is kept low; as the sludge inventory grows, the return sludge flow is raised to match. Once the concentration reaches the value the process needs, normal operation and process control begin.
2. Continuous cultivation. Fill the aeration tank with wastewater, stop the feed and aerate for half a day to a day, then begin continuous feeding. Aeration runs continuously and the flow is raised gradually from small to large. After a period of continuous running comparable to the batch method, activated sludge appears and then builds up. When the sludge inventory reaches the concentration the process needs, control follows the process requirement.
Because natural cultivation uses the wastewater itself, the cultivation is at the same time the process by which the micro-organisms adapt to that wastewater and become acclimated to it.
Seeding with Imported Sludge
Seeding takes less time and is the method most industrial wastewater plants use. A municipal plant can also use it where seed sludge is available nearby, to shorten the cultivation period. Two forms are common.
1. Thickened sludge seeding. Thickened sludge from a neighbouring plant serves as the seed. For municipal sewage, and for industrial wastewater that is nutritionally complete and low in toxicity, the seed is added directly to the wastewater in the aeration tank and aerated until the sludge turns brownish yellow; continuous feed can then begin, increasing gradually, and the clarifier is brought into service so that the sludge circulates through the system. To speed up the process, unfermented night soil or other nutrients can be dosed during cultivation. Cultivation is complete when the mixed liquor concentration reaches the design value. Economically the seed dose should be as small as possible — normally enough to give a mixed liquor concentration above 0.5 g/L after dilution.
For toxic industrial wastewater, first fill the aeration tank with river water, or with tap water that has been aerated for a while to strip residual chlorine. Then add seed sludge and unfermented night soil and aerate until the sludge turns brownish yellow. Stop the air, let the sludge settle, draw off part of the supernatant, top up with a measured amount of night soil and aerate again. Once the sludge volume has clearly increased, raise the wastewater flow step by step. By the later stage of cultivation the biomass is reasonably well adapted to the industrial wastewater.
2. Dried sludge seeding. Dried sludge normally means the cake that comes off a dewatering machine at about 70 to 80 percent moisture. This method suits remote sites where seed sludge cannot be hauled far.
The procedure is essentially the same as for thickened sludge. Use fresh cake that has been dewatered recently; before adding it to the tank, add a little water and mash it into a slurry. The usual dose is 2 to 5 percent of the tank volume.
Dried sludge may carry conditioning chemicals. If the chemical content is high and the toxicity significant, the sludge is not suitable as seed. To test it, mash a small amount of cake in a beaker or plastic pail, add water and aerate; if the colour turns yellow after a period, the sludge can be used.
Points to Watch During Cultivation
1. Measure influent pH, COD and ammonia nitrogen, and the dissolved oxygen and settleability of the aeration tank, at frequent intervals. Once sludge has begun to form, examine the biomass under the microscope, judge the state of cultivation from what is seen and adjust the process dynamically.
2. Cultivate in a warm season wherever possible: micro-organisms grow quickly in warm conditions and the cultivation period is short. If cultivation must be done in winter, use the seeding method and dose more seed sludge than would be needed in spring or autumn.
3. Guard against over-oxidation of the sludge, especially once it has formed and especially in summer. Plenty of plants have run into this. It lengthens cultivation and raises its cost, and it can stop a plant going into service on schedule. The key is to control the aeration rate and the aeration time, to measure dissolved oxygen in the tank frequently, and to feed in good time so that the biomass gets the nutrients it needs. If the influent is too weak, add night soil or a similar material to make up the nutrient, or use intermittent aeration where nothing better is available.
4. In the later stage of cultivation, wasting a little old sludge helps the micro-organisms multiply further.
5. An industrial plant often has no wastewater until the production units start up, and once they do the effluent must be treated straight away. Judge the cultivation period realistically and prepare seed sludge and nutrients in advance.
6. If the sludge is already mature but no wastewater has arrived, stop the air and let the sludge rest, or aerate intermittently — longer intervals, lower air rate — to slow self-oxidation as far as possible. Where conditions allow, dose night soil or a non-toxic organic waste such as canteen food waste.
7. Most wastewater plants have two or more aeration tanks. In that case cultivate in one tank first, then transfer the sludge to the neighbouring tanks for multi-stage scale-up. This is the method suited to larger plants.